So hier der Bootlog von einem Siemens blue2net:
PPCBoot 1.0.1.5 (Feb 7 2002 - 16:32:24)
Initializing…
CPU: XPC850xxZTB at 48.400 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming ETX_094
HW-Version: V0.9 / W50037-Q1-D6-1
RSR: 0xc0000000
DRAM: 16 MB
FLASH: 2 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 5 4 3 2 1 0
## Booting image at 40020000 …
Image Name: Linux-2.4.9_for_ETX_094+SCCUART+
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 1879088 Bytes = 1835 kB = 1 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 472019 Bytes = 460 kB = 0 MB
Image 1: 1407056 Bytes = 1374 kB = 1 MB
Verifying Checksum … OK
Uncompressing Multi-File Image … OK
Loading Ramdisk to 00df4000, end 00f4b850 … OK
Linux version 2.4.9 (root@atpcp88c.erd.siemens.at) (gcc version 2.95.3 20010315 (release/MontaVista)) #148 Fri Jan 24 10:46:10 CET 2003
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram rw ramdisk_size=4096 ppcboot_version=ppcboot-1.0.1.5-20020207 panic=1 ip=::::::auto
Decrementer Frequency = 151250000/50
Calibrating delay loop… 48.02 BogoMIPS
Memory: 13348k available (892k kernel code, 408k data, 56k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
CPM UART driver version 0.03
ttyS0 on SMC1 at 0×0280, BRG1
pty: 256 Unix98 ptys configured
WDT_8xx: Software Watchdog Timer version 0.2
>>etxhwif LAP HW Interface driver version 0.1 started<<
compiled Jan 24 2003 10:46:41
MAJOR 10, MINOR 150
>> hwid output enabled
Found 1×16bit 2MByte CFI flash device of type AMD/Fujitsu standard at 40000000
Registered flash device /dev/flasha (minor 0, 4 partitions)
block: 64 slots per queue, batch=8
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eth0: CPM ENET Version 0.2 on SCC2, 08:00:06:60:5c:ef
64 RX Buffers, 64 TX Buffers
loop: loaded (max 8 devices)
PPP generic driver version 2.4.1
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Sending DHCP requests … timed out!
IP-Config: Reopening network devices…
Sending DHCP requests … timed out!
IP-Config: Auto-configuration of network failed.
ip_conntrack (128 buckets, 1024 max)
ip_tables: (c)2000 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1374k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 56k init
INIT: version 2.78 booting
INIT: Entering runlevel: 3
uart_bluetooth.c uart_bt_init: uart_bluetooth inserted, compiled at Apr 16 2002 17:25:42
BNEP driver version 0.20
NET4: Ethernet Bridge 008 for NET4.0
Siemens blue2net BT-LAP administration software.
Version: 4.0.0 Compilation time: Thu May 15 13:21:16 CEST 2003
blue2net-4.1.0
business_1
******************************************************************
* architecture = ppc for ETX_094
* crosstools = hhl
* static_linking = no
* debug compilation = off
* debug defines = off
* debug input = off
* transport layer = uartchar
* kernel = 2.4.9
* bluetooth version = 1-1
* bluetooth module = csr
* CLIENTSERVER = on
* ramdisc type = custom
* ramdisc size = 4096
* optimized libraries = on
* compilation date = 20030515
* compilation time = 13:20
* silent mode = on
* BNEP = on
******************************************************************
* use pseudo terminals = on
******************************************************************
* btadminsb 4.0.0
* stack 0.54.1
* SNMP 0.1.2
******************************************************************
BTADMINSB_LOG-4.0.0 00:00:39.205: src/btadminsb.c startChildProcess line: 2532: started process /bin/rbtd with arg rbtd -n ; PID: 19
rbtd: BT stack Vers. May 15 2003 13:22:03, TL-dev: /dev/cfUaB0, DL-dev: /dev/ptyq, PID: 19
rbtd: compiled for CSR module; BAUD 6
RBTD-TrStr 00:00:39.518 rb_tl.c :1403 - INITIALISE TL interface name: /dev/cfUaB0.
BTADMINSB_LOG-4.0.0 00:00:40.830: src/btadminsb.c checkFlashConfig line: 3094: Flash size = 2097152 (0×200000); LAP config file sector starts at 0×1F0000
BTADMINSB_LOG-4.0.0 00:00:40.856: src/btadminsb.c copyConfigFilesFromFlashToFilesystem line: 3189: config files found in flash: take it
BTADMINSB_LOG-4.0.0 00:00:40.975: src/btadminsb_flash.c readConfigFilefromFlash line: 885: trusted link keys found: take it
Absolute path detected, removing leading slashes
No matches
No matches
BTADMINSB_ERR-4.0.0 00:00:41.856: src/btadminsb.c get_ifconf line: 870: ioctl to get IP address failed with -1
BTADMINSB_ERR-4.0.0 00:00:42.037: src/btadminsb.c get_ifconf line: 870: ioctl to get IP address failed with -1
BTADMINSB_ERR-4.0.0 00:00:42.310: src/btadminsb.c get_ifconf line: 870: ioctl to get IP address failed with -1
BTADMINSB_ERR-4.0.0 00:00:42.693: src/btadminsb.c initAll line: 4063: Can’t get own IP
BTADMINSB_ERR-4.0.0 00:00:43.337: src/btadminsb.c reboot line: 2942: Reboot because Reboot because LAP IP parameter changed !! !!
input from stdin disabled
RBTD-TrStr 00:00:44.158 rb_osadp.c: 184 - Flash Info read: 2000
RBTD-TrStr 00:00:46.191 rb_osadp.c:1055 - bFlash2Ram 0×1005ee64 len: 1904 offset: 0
RBTD-TrStr 00:00:46.207 rb_panc.c :1706 - PANC initialised
RB proc entering looping
RBTD-TrStr 00:00:46.981 rb_cl.c : 326 - Init TrustedDeviceList, read 4 devices
RBTD-TrStr 00:00:46.993 rb_osadp.c:1103 - bRam2Flash 0×1005ee64 len: 6 offset: 0 ignored
RBTD-TrStr 00:00:47.011 rb_panc.c :1721 - PANC shutting down
rbtd stopped
opening
r
PPCBoot 1.0.1.5 (Feb 7 2002 - 16:32:24)
Initializing…
CPU: XPC850xxZTB at 48 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming ETX_094
HW-Version: V0.9 / W50037-Q1-D6-1
RSR: 0xc0000000
DRAM: 16 MB
FLASH: 2 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 5 4 3 2 1 0
## Booting image at 40020000 …
Image Name: Linux-2.4.9_for_ETX_094+SCCUART+
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 1879088 Bytes = 1835 kB = 1 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 472019 Bytes = 460 kB = 0 MB
Image 1: 1407056 Bytes = 1374 kB = 1 MB
Verifying Checksum … OK
Uncompressing Multi-File Image … OK
Loading Ramdisk to 00df4000, end 00f4b850 … OK
Linux version 2.4.9 (root@atpcp88c.erd.siemens.at) (gcc version 2.95.3 20010315 (release/MontaVista)) #148 Fri Jan 24 10:46:10 CET 2003
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram rw ramdisk_size=4096 ppcboot_version=ppcboot-1.0.1.5-20020207 panic=1 ip=192.168.1.2:192.168.1.253:192.168.1.1:255.255.255.0:::off
Decrementer Frequency = 150000000/50
Calibrating delay loop… 47.61 BogoMIPS
Memory: 13348k available (892k kernel code, 408k data, 56k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
CPM UART driver version 0.03
ttyS0 on SMC1 at 0×0280, BRG1
pty: 256 Unix98 ptys configured
WDT_8xx: Software Watchdog Timer version 0.2
>>etxhwif LAP HW Interface driver version 0.1 started<<
compiled Jan 24 2003 10:46:41
MAJOR 10, MINOR 150
>> hwid output enabled
Found 1×16bit 2MByte CFI flash device of type AMD/Fujitsu standard at 40000000
Registered flash device /dev/flasha (minor 0, 4 partitions)
block: 64 slots per queue, batch=8
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eth0: CPM ENET Version 0.2 on SCC2, 08:00:06:60:5c:ef
64 RX Buffers, 64 TX Buffers
loop: loaded (max 8 devices)
PPP generic driver version 2.4.1
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
IP-Config: Complete:
device=eth0, addr=192.168.1.2, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.2, domain=, nis-domain=(none),
bootserver=192.168.1.253, rootserver=192.168.1.253, rootpath=
ip_conntrack (128 buckets, 1024 max)
ip_tables: (c)2000 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1374k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 56k init
INIT: version 2.78 booting
INIT: Entering runlevel: 3
uart_bluetooth.c uart_bt_init: uart_bluetooth inserted, compiled at Apr 16 2002 17:25:42
BNEP driver version 0.20
NET4: Ethernet Bridge 008 for NET4.0
Siemens blue2net BT-LAP administration software.
Version: 4.0.0 Compilation time: Thu May 15 13:21:16 CEST 2003
blue2net-4.1.0
business_1
******************************************************************
* architecture = ppc for ETX_094
* crosstools = hhl
* static_linking = no
* debug compilation = off
* debug defines = off
* debug input = off
* transport layer = uartchar
* kernel = 2.4.9
* bluetooth version = 1-1
* bluetooth module = csr
* CLIENTSERVER = on
* ramdisc type = custom
* ramdisc size = 4096
* optimized libraries = on
* compilation date = 20030515
* compilation time = 13:20
* silent mode = on
* BNEP = on
******************************************************************
* use pseudo terminals = on
******************************************************************
* btadminsb 4.0.0
* stack 0.54.1
* SNMP 0.1.2
******************************************************************
BTADMINSB_LOG-4.0.0 00:00:11.701: src/btadminsb.c startChildProcess line: 2532: started process /bin/rbtd with arg rbtd -n ; PID: 19
rbtd: BT stack Vers. May 15 2003 13:22:03, TL-dev: /dev/cfUaB0, DL-dev: /dev/ptyq, PID: 19
rbtd: compiled for CSR module; BAUD 6
RBTD-TrStr 00:00:12.023 rb_tl.c :1403 - INITIALISE TL interface name: /dev/cfUaB0.
BTADMINSB_LOG-4.0.0 00:00:13.341: src/btadminsb.c checkFlashConfig line: 3094: Flash size = 2097152 (0×200000); LAP config file sector starts at 0×1F0000
BTADMINSB_LOG-4.0.0 00:00:13.368: src/btadminsb.c copyConfigFilesFromFlashToFilesystem line: 3189: config files found in flash: take it
BTADMINSB_LOG-4.0.0 00:00:13.488: src/btadminsb_flash.c readConfigFilefromFlash line: 885: trusted link keys found: take it
Absolute path detected, removing leading slashes
No matches
No matches
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
BTADMINSB_ERR-4.0.0 00:00:14.410: src/btadminsb.c setNetInterfaceUpDown line: 1057: socket ioctl to set brNAP:0 to DOWN failed with -1
BTADMINSB_LOG-4.0.0 00:00:16.524: src/btadminsb.c startChildProcess line: 2532: started process /home/httpd/mini_httpd with arg mini_httpd -u config -c cgi-bin/snmp_cgi -S ; PID: 61
BTADMINSB_LOG-4.0.0 00:00:16.572: src/btadminsb.c main line: 4513: reboot counter = 1
input from stdin disabled
RBTD-TrStr 00:00:16.664 rb_osadp.c: 184 - Flash Info read: 2000
mini_httpd: started as root without requesting chroot(), warning only
BTADMINSB_LOG-4.0.0 00:00:16.996: src/btadminsb_dev_handler.c readBtadminDriver line: 2101: Child with PID 61 dead; status: 0
RBTD-TrStr 00:00:18.741 rb_osadp.c:1055 - bFlash2Ram 0×1005ee64 len: 1904 offset: 0
RBTD-TrStr 00:00:18.757 rb_panc.c :1706 - PANC initialised
RB proc entering looping
RBTD-TrStr 00:00:19.533 rb_cl.c : 326 - Init TrustedDeviceList, read 4 devices
RBTD-TrStr 00:00:19.546 rb_osadp.c:1103 - bRam2Flash 0×1005ee64 len: 6 offset: 0 ignored
RBTD-TrStr 00:00:19.565 rb_cl.c :1479 - msgOstChgReq UP received, forceMasterSlaveSwitch: 1
BTADMINSB_ERR-4.0.0 00:00:19.580: src/btadminsb.c setTimeOverTimeServer line: 3058: No time server IP defined
BTADMINSB_LOG-4.0.0 00:00:19.598: src/btadminsb.c setTimeOverTimeServer line: 3071: LAP Time used from internal: Thu Jan 1 00:00:19 1970
RBTD-TrStr 00:00:19.643 rb_cl.c :1729 - Add Service record_id: 0×0001, name: LAN ACCESS, index: 0, DLCI: 0×02, Auth: 2, profil: 0×1102, sdb_db_index: 0 added
RBTD-TrStr 00:00:19.668 rb_cl.c :1729 - Add Service record_id: 0×0002, name: PAN NAP , index: 1, DLCI: 0×00, Auth: 2, profil: 0×1116, sdb_db_index: 1 added
RBTD-TrStr 00:00:19.703 rb_cl.c :1729 - Add Service record_id: 0×0003, name: PAN GN , index: 2, DLCI: 0×00, Auth: 2, profil: 0×1117, sdb_db_index: 5 added
RBTD-TrStr 00:00:19.731 rb_cl.c :1904 - lapName: blue2net 192.168.1.2
BTADMINSB_LOG-4.0.0 00:00:19.748: src/btadminsb_dev_handler.c readBtadminDriver line: 1859: OstChgdEv operstat = 1
RBTD-TrStr 00:00:19.840 rb_osadp.c:1103 - bRam2Flash 0×1005ee64 len: 16 offset: 6 ignored
RBTD-TrStr 00:00:19.887 rb_cl.c : 453 - New TrustedDevice addr 00:12:37:4d:0b:b9:
RBTD-TrStr 00:00:19.899 rb_cl.c :2293 - Flash access for trusted devices enabled
BTADMINSB_LOG-4.0.0 00:00:20.882: src/btadminsb_dev_handler.c readBtadminDriver line: 2007: BCCMDR response success = 1; frame = 7FFFF514
BTADMINSB_LOG-4.0.0 00:00:20.950: src/btadminsb_dev_handler.c readBtadminDriver line: 2077: SieMo Modul Info response success = 1; content: S50037-Q5-X105-2 Si-5.0a-V0000(02-06-25) UART-5.0-c2(02-06-25) 00128-013.10-0136-01
BTADMINSB_LOG-4.0.0 00:00:21.105: src/btadminsb_dev_handler.c readBtadminDriver line: 1919: Firmware info received: 013601010a003601
BTADMINSB_LOG-4.0.0 00:00:21.360: src/btadminsb.c startChildProcess line: 2532: started process /home/httpd/cgi-bin/snmpd with arg snmpd -f -p 161@127.0.0.1 ; PID: 67
SNMPD SiemensBtLapMib_init.c:3697, ‘read /etc/terminal.txt’
SNMPD SiemensBtLapMib_init.c:3716, ‘read /etc/service.txt’
SNMPD SiemensBtLapMib_init.c:3735, ‘read /etc/config_ppp_bt.txt’
SNMPD SiemensBtLapMib_init.c:3754, ‘read /etc/data.txt’
SNMPD SiemensBtLapMib_init.c:3774, ‘read /etc/ether_terminal.txt’
SNMPD SiemensBtLapMib_init.c:3794, ‘read /etc/config_port_forward.txt’
SNMPD SiemensBtLapMib_init.c:3815, ‘MIB load finished’
SNMPD: installing master agent on port 161@127.0.0.1
0 Responses to “Siemens blue2net Log”
Leave a Reply